PVC Bendit Testimonials

Words of praise from our happy clients.

The original bender was assembled and sent out the same day as ordered. Exceptional service... We purchased the unit for a rather unconventional use. Oskaloosa has a lighted Christmas parade each year and Musco builds a float for. This years float was a over sized sleigh that used 3" Schedule 40 electrical PVC for the runners. The conduit needed to curve up at the front of the runner and that is what we were going to use the bender for.

Thank you for introducing me to PVC Bendit - the examples of the work in your site are terrific, particularly the complex spiral and free-form multi-planar shapes. Beautiful. I feel this kind of need comes up fairly regularly in my stage design work and I'm glad to have source to turn to next time 'round. (So to speak.)

There might well be an entire early twentieth century European restaurant kitchen in my next Opera commission - your techniques would be a marvelous way to reach easily a wonderful looking complicated level of realism.

I'll keep in touch,

Yours,

My nephew bought one of these about four months ago to work on his hydro garden. He was meaning to do an add on for a long time, but he wanted to learn from mistakes that he'd made in the past and just make a better setup. He won't stop talking about the darn thing. Now he's a consultant for other gardeners, and this one tool is the thing that put him in business. Thank you for what you're making, it's helping my nephew make a living. Keep up the good work, guys.

Jim F.
Austin, TX

...We had a client who wanted us to wind his outdoor lighting conduits around a columnade like vines. We were far enough into the job that we had to accept the change order, but we had a hard time making it work. Our heat guns were not doing the job, I can tell you that much. I took a little time to do some research, and I found this tool. We were able to do the job so easily that I already can't remember life before PVC Bendit. This is my go to tool now for any conduit bending that I have to do. Next time I get a plumbing gig, I'm gonna see if this thing can help me make a lower bid, and I'll never do another electrical job without it. You guys saved my butt. Thanks.

anonymous handyman
(from voicemail)

Vic,
My whole department is excited about your product. In Theatre we've been bending PVC for many years, but our methods were all terrible. As I'm sure you know, filling it with sand and heating it from the outside with heat guns and blow torches just doesn't work very well, and the lovely black smoke is a serious problem.

I intend to not only use your product for our next show, one of our graduate students is going to put together a poster presentation on it. If everything goes as smoothly as I expect you can expect some coverage from us....

....At any rate, we look forward to our useful new tool/toy.

Patrick Stone
University of Arkansas

Hi Vic,

I am an engineer in the ADC, (advanced developmental composites) for Boeing and I have been showing this system to a few of my fellow engineers... I think you might get some more orders from here....

Anyway, I am going to be working on 1/2 inch and 3/4 inch. I was going to make some greenhouses and also some candy canes for Christmas decorations.

I am also thinking about making a portable chicken coop, and a boat garage... If you know anything about the weather here, boating is great for 3 months out the year, then it has to be covered for the other nine....

Take Care

Dan

....I have two projects immediately in mind: some low voltage sprinkler control and landscape lighting wiring to be run in 1 1/4" PVC underground from a Christie box to the foundation of one of the buildings on our campus, and a series of communications cable homeruns between buildings that I want to sheath with 3/4" conduit. I'm looking forward to getting precisely the geometry I want without having to resort to a variety of premade fittings with standard sweeps; especially in the comm wiring, since some of it will be mounted under the eaves of our sanctuary, where any sign of kludginess will just draw (unwanted) attention to the installation. Nothing that hasn't already been done with your tool, but exciting for me nonetheless.

Kind Regards,
Mark Knight
Saint Bede's Episcopal Church

“Just wanted to say thanks for getting me the equipment so quickly. I have attached a picture of successfully bending a 2.5” White schedule 40 PVC as well as 2.5” Harvel clear schedule 40 PVC pipe into a 9.25” radius. Everything worked out fantastic and we’ll be testing things next week.“

Anonymous Aerospace Client

Vic,

The show we bought the tool for is the next one, but we snuck in one small bend for this show, and the Bendit is awesome, I'll keep you posted when we start doing large scale sculpting.

Dear Vic,

Thank you so much for the voice mails and emails.  Your Customer Service has been great!

We opened our Fall Musical, "Anything Goes," last Friday and have one more weekend of performances.  So, the reason I haven't responded yet is simply I was so busy getting the show up & running!  In case you don't know the play ,it is set on an ocean liner in 1934.  Our set design included Art Deco lines, so the Bendit tool was perfect for creating curved railings that were painted a brass color.  We also used it to make a headboard for a bed in the Upper Class stateroom.

I did have a photographer take shots of the show, so I will have to send those to you soon.  Also, I wasn't the person who actually used the Bendit, so I have asked the gentlemen who had "hands-on" experience to give me some feedback as well.  I know they thought it was great, but I'm sure you would appreciate something more specific.

Again- thanks for a great product, very quick delivery and fantastic customer service!

Mary Mitchell-Donahue
Bishop McNamara High School
Theatre Director
Fine Arts Department Chair

Vic, this will transform how we do frames and open up all sorts of new opportunities!

Rachel Porter, CBA
Balloon Splendor

Hi Vic,

I've received the PVC Bendit and used it yesterday on the 1 1/4" sched 40 electrical conduit I needed to form with a complex bend.  It worked well, and I'm pleased.

www.pvcbendit.com